This chapter describes the syntax rules for referring to properties and for creating expressions within various DTL actions. It contains the following sections:
References to Message Properties
In most actions within a transformation, it is necessary to refer to properties of the source or target messages. The rules for referring to a property are different depending on the kind of messages you are working with.
For messages other than virtual documents, use syntax like the following:
source.propertynameCopy code to clipboard
source.propertyname.subpropertynameCopy code to clipboard
Where propertyname is a property in the source message, and subpropertyname is a property of that property.
If the message includes a collection property, see “Special Variations for Repeating Fields” in “Virtual Property Path Basics” in the Ensemble XML Virtual Document Development Guide. Some of the information there applies to both virtual documents and standard messages.
For virtual documents other than XML virtual documents, use the syntax described in “Syntax Guide for Virtual Property Paths” in Ensemble Virtual Documents. Also see the following subsection.
For XML virtual documents, see the Ensemble XML Virtual Document Development Guide.
When you assign a value to a target property, you often specify a literal value. Literal values are also sometimes suitable in other places, such as the value in a trace action.
A literal value is either of the following:
A numeric literal is just a number. For example: 42.3
A string literal is a set of characters enclosed by double quotes. For example: "ABD"Note:
This string cannot include XML reserved characters. For details, see “XML Reserved Characters.”
For virtual documents, this string cannot include separator characters used by that virtual document format. See “Separator Characters in Virtual Documents” and “When XML Reserved Characters Are Also Separators.”
Due to the limitations of single-byte encoding format for HL7, the numeric value in character codes in literal strings placed in HL7 messages can be no higher than the decimal value 255 or hexadecimal x00FF.
XML Reserved Characters
Because DTL transformations are saved as XML documents, you must use XML entities in the place of XML reserved characters:
|To include this character...||Use this XML entity...|
For example, to assign the value Joe’s "Good Time" Bar & Grill to a target property, set Value equal to the following:
"Joe's "Good Time" Bar & Grill"
This restriction does not apply inside code and sql actions, because Ensemble automatically wraps a CData block around the text that you enter into the editor. (In the XML standard, a CData block encloses text that should not be parsed as XML. Thus you can include reserved characters in that block.)
Separator Characters in Virtual Documents
In most of the virtual document formats, specific characters are used as separators between segments, between fields, between subfields, and so on. If you need to include any of these characters as literal text when you are setting a value in the message, you must instead use the applicable escape sequence, if any, for that document format.
These characters are documented in the applicable books. For details, see:
“Separators” in the reference section of the Ensemble HL7 Version 2 Development Guide
“Separators” in the reference section of the Ensemble ASTM Development Guide
“Separators” in the reference section of the Ensemble EDIFACT Development Guide
“Separators” in the reference section of the Ensemble X12 Development Guide
In a data transformation, the separator characters and escape sequences can be different for the source and target messages. Ensemble automatically adjusts values as needed, after performing the transformation. This means that you should consider only the separator characters and escape sequences that apply to the source message.
When XML Reserved Characters Are Also Separators
If the character (for example, &) is a separator and you want to include it as a literal character, use the escape sequence that applies to the virtual document format.
In all other cases, use the XML entity as shown previously in “XML Reserved Characters.”
Numeric Character Codes
You can include decimal or hexadecimal representations of characters within literal strings.
The string &#n; represents a Unicode character when n is a decimal Unicode character number. One example is é for the Latin e character with acute accent mark (é).
Alternatively, the string &#xh; represents a Unicode character when h is a hexadecimal Unicode character number. One example is ¿ for the inverted question mark (¿).
When you assign a value to a target property, you can specify an expression, in the language that you selected for the data transformation. You also use expressions in other places, such as the condition for an if action, the value in a trace action, statements in a code action, and so on.
The following are all valid expressions:
Literal values, as described in the previous section.
Function calls (Ensemble provides a set of utility functions for use in business rules and data transformations. For details, see “Ensemble Utility Functions” in Developing Business Rules.) Ensemble provides a wizard for these.
References to properties, as described in “References to Properties.”
References to the aux variable passed by the rule. If the data transformation is called from a rule, it supplies the following information in the aux variable:
aux.BusinessRuleName—Name of the rule.
aux.RuleReason—Reason that the rule was fired. It is the same name as used in the logging. An example value is 'rule#1:when#1'. If the RuleReason is longer than 2000 characters, it is truncated to 2000 characters.
aux.RuleUserData—Value that was assigned in the rule to the property 'RuleUserData'.
If the data transformation is called directly from code and not from a rule, the code can pass the auxiliary data in the third parameter. If your data transformation may be called from code that does not set the third parameter, your DTL code should check that the aux variable is an object in an if action using the $ISOBJECT function.
Any expression that combines these, using the syntax of the scripting language you chose for data transformation. See “Specifying Transformation Details,” earlier in this book. Note the following:
In ObjectScript, the concatenation operator is the _ (underscore) character, as in:
In Basic, the concatenation operator is & (ampersand).